May 4, 2016 - Marshall DSL50W Head Tone Issues. And when I add pedals to the mix I seem to lose a lot of definition in my tone. I'm not getting that classic Marshall tone, I can get a nice clean channel but. Honestly a DSL is a masterpiece of an amp and is a Jack of all Trades and a. Marshall JCM2000 DSL100.
Potentiometers - Marshall® Bias Click on photo for larger view POT, 22K VERTICAL LINEAR BIAS ADJUST POT FOR Marshall® Used in many previous Marshall® models with PC board circuitry. Mounted on the main PC board - used to set the bias on the output tubes. Common failure item. This is the original Marshall® part.
Body of pot is 15mm (about 5/8') in diameter. Part #P-BPM-22KL-V $2.95 Quantity: Click on photo for larger view POT, 22K HORIZONTAL LINEAR BIAS ADJUST POT FOR Marshall® - TYPE 1 Mounted on the main PC board or turret boards - used to set the bias on the output tubes.
This style has 2 pins plus 2 tabs for mounting - see photo. Common failure item.
This is an alternate horizontal style - particularly useful in modifications, kit builds, etc. Body of pot is 15mm (about 5/8') in diameter. Part #P-BPM-22KL-H1 $2.95 Quantity: Click on photo for larger view POT, 22K HORIZONTAL LINEAR BIAS ADJUST POT FOR Marshall® - TYPE 2 Mounted on the main PC board or turret boards - used to set the bias on the output tubes. This style has 3 pins for mounting - see photo. Common failure item.
This is an alternate horizontal style - particularly useful in modifications, kit builds, etc. Body of pot is 15mm (about 5/8') in diameter. Part #P-BPM-22KL-H2 $2.95 Quantity: Click on photo for larger view POT, JCM2000 SERIES 22K LINEAR BIAS ADJUST POT FOR Marshall® Marshall part number POTTR22K, used as bias adjust pots. Found in the DSL-50, DSL-100, TSL-100, TSL-122 models in the JCM2000. Each amplifier uses two bias pots. Part #POT-TR22K $3.50 Quantity: Potentiometers - Marshall® 24mm (JCM800) Click on photo for larger view P OT, ORIGINAL Marshall®, PC MOUNT, 24mm DIAMETER BODY, 9.5mm DIAMETER THREADED BUSHING. Used in many previous Marshall® models with PC board circuitry (such as the later JCM800 series).
Original Marshall replacement with 8.8mm (nominal 9mm) diameter threaded bushing. Bushing length is 9.5mm.
Diameter of the body of the pot is the size of a quarter (about 1 inch or 24mm). Includes washer and two nuts. Replacement nut is the JN-975. Select Pot Value in Options Part #P-VM24-XX $5.95 Note - the B22K size is currently unavailable from Marshall.
Use the B22K in the P-VM24AP style pot below as an alternative. Select Option: Quantity: Click on photo for larger view ALTERNATIVE POT, AFTERMARKET Marshall® TYPE, PC MOUNT, 24mm DIAMETER BODY, 8mm DIAMETER THREADED BUSHING. This is an alternative pot for 24mm Marshall pots - made by Alpha. 7.8mm (nominal 8mm) diameter threaded bushing. Bushing length is 10.5mm. Diameter of the body of the pot is the size of a quarter.
This pot has a smaller diameter bushing than the original - however, unlike many other suppliers, we include all necessary washers (2) and nuts (3) to be a drop-in replacement for the original Marshall® pot. Replacement nut is our JN-1016. Select Pot Value in Options Part #P-VM24AP $4.95 Select Option: Quantity: Click on photo for larger view P OT, A1M WITH SPST PULL SWITCH, Marshall®, PC MOUNT, 24mm DIAMETER BODY, 9.5mm DIAMETER THREADED BUSHING. May be used as a replacement for the gain control in the Marshall® model 3210 Lead 100 MOSFET Head. Marshall replacement with 9.5mm diameter threaded bushing.
Bushing length is 9.5mm. Diameter of the body of the pot is the size of a quarter (about 1 inch or 24mm). SPST switch on back of the pot,activated by pulling the pot knob. Includes washer and two nuts.
Replacement nut is the JNUT-38. Marshall part number POTP-00026. Part #P-VM24-A1M-PS $14.95 Quantity: Click on photo for larger view P OT, A1M DUAL TANDEM, Marshall®, PC MOUNT, 20mm DIAMETER BODY, 9.5mm DIAMETER THREADED BUSHING. Replacement for tandem A1M pots used in 1980s vintage Marshall amps, such as certain JCM800 models and a few solid state models. Replacement with 9.5mm diameter threaded bushing. Bushing length is 10.5mm.
Note that this pot is NOT PC mount, and so it requires hard wiring to the PC board. The original tandem pots are no longer available. Knurled nylon shaft, for push-on knobs. Includes lock washer and nut.
Marshall part number MPOTM-00003. Part #P-VM24-A1MX2 $10.95 Quantity: Click on photo for larger view POT NUT, METAL Replacement metric nut for the Marshall® 24mm pots (P-Vxxxx-M24) which have brass colored threaded bushings. These nuts typically fit the original pots used in vintage Marshalls, and the original Marshall® replacement pots that we sell. For the matching washer, see the JW-9. The JN-975 does not fit the newer Alpha replacement 24mm pots which have silver colored threaded bushings - for those pots, see our JN-1016 8mm nut. Part #JN-975 $0.49 Quantity: Click on photo for larger view POT WASHER, METAL Replacement metric washer for the Marshall® 24mm pots (P-Vxxxx-M24) which have brass colored threaded bushings. 9mm ID, 15mm OD. These washers typically fit the original pots used in vintage Marshalls, and the original Marshall® replacement pots that we sell.
They do not fit 3/8' diameter pot bushings (such as pots in vintage Fender amps), or Switchcraft jacks. Part #JW-9 $0.19 Quantity: Click on photo for larger view POT NUT, METAL, 8MM Replacement nut for the Fender® bracket mount pots with smooth 1/4' shafts (FPHD-xxxx), such as used on the Hot Rod Deluxe/Deville, Blues Deluxe/Deville. Also fits the substitute replacement pots for Marshall® 24mm with silver-colored threaded bushings, our P-VA-XX pots, the P-8M-2X250KA and P-8M-2X1MA dual pots, and the P-V1MA-MV master volume with pull switch pot. Part #JN-1016 $0.39 Quantity: Click on photo for larger view POTENTIOMETER DUST CAP, for all 16mm (5/8') pots.
Slips over the case of the pot and helps keep out dust and contamination. Made by Alpha. Fits all 16mm potentiometers. Sold in packs of 4. Note: For single-gang pots only - will not fit dual 16mm pots. Part #PDC-160 $0.69 (For a pack of 4 dust caps) Quantity: Click on photo for larger view SAVE WITH MULTIPACK! JNUT-38 JACK NUT AND WASHER, METAL, SWITCHCRAFT®, SET OF 6 Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8' bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4' jacks.
Does NOT fit the 24mm Marshall® pots. Set of 6 washers and 6 nuts. Part #JNUT-38-6 $4.50 (Set of 6 washers and 6 nuts) Quantity: JACK NUT AND WASHER, METAL, SWITCHCRAFT® Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8' bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4' jacks. Does NOT fit the 24mm Marshall® pots. Part #JNUT-38 $0.89 (Set of 1 washer and 1 nut) Quantity: Click on photo for larger view JACK LOCK WASHER, METAL Replacement lock washer for all Alpha pots with 3/8' bushing and Mesa Boogie pots, as well as Switchcraft 1/4' jacks.
Part #W-38 $0.49 Quantity: 16mm Potentiometers, Long Shaft Length (Marshall® Style - JCM900 and Valvestate Version 1) Click on photo for larger view POT, PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING. ORIGINAL Marshall® REPLACEMENT PART. Used in Marshall® Valvestate I, JCM900 and JCM600 Series. Used in Marshall® models: 8040, 8080, 8100, 8200, 8240, 8280, JCM900 Models: 2100, 2101, 2500, 2501, 4100, 4500, 4101, 4102, 4501, 4502, SL-X 2100, SL-X 2500, 6100, 6101, JTM600 and JTM30 Series. Also used in other amps besides Marshall®. Available values: B4.7K, B10K, B22K, B50K, A100K, B100K, B220K, and A1M. Select Pot Value in Options INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-VM16-XX $2.95 Select Option: Quantity: Click on photo for larger view POTENTIOMETER DUST CAP, for all 16mm (5/8') pots.
Slips over the case of the pot and helps keep out dust and contamination. Made by Alpha. Fits all 16mm potentiometers. Sold in packs of 4. Note: For single-gang pots only - will not fit dual 16mm pots. Part #PDC-160 $0.69 (For a pack of 4 dust caps) Quantity: Click on photo for larger view POT, 10K OHM X2 LINEAR DUAL, (B10K), PC MOUNT, 6 MOUNTING PINS, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING. Used in Marshall® Valvestate I, JCM900 and JCM600 Series.
Also used in the JMP1 Preamp as Output Level Control. Used in Marshall® models: 8080, 8100, 8200, 8240, 8280, JCM900 Models: 4100, 4500, 4101, 4102, 4501, 4502, SL-X 2100, SL-X 2500, 6100, 6101, JTM600 and JTM30 Series. Diameter of the body of the pot is slightly smaller than a dime.
Shaft length is 11.5mm. Fits many other amps besides Marshall®.
INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-V10KLX2-M16 $6.95 Quantity: Click on photo for larger view POT, 100K OHM X2 REVERSE AUDIO DUAL, (C100K), PC MOUNT, 6 MOUNTING PINS, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING. Diameter of the body of the pot is slightly smaller than a dime. Shaft length is 11.5mm.
Fits many other amps besides Marshall®. INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-V100KRAX2-M16 $6.95 Quantity: Other Long Shaft 16mm Potentiometers: Click on photo for larger view POT, 10K OHM AUDIO, (A10K), PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING. Used in Marshall® and other amps, including the Marshall 8015 keyboard amp. INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-V10KA-M16 $2.95 Quantity: Click on photo for larger view POT, 250K OHM AUDIO, (A250K), Marshall® TYPE, PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING.
Diameter of the body of the pot is slightly smaller than a dime. Shaft length is 11.5mm. INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-V250KA-M16 $2.95 Quantity: Click on photo for larger view POT, 250K OHM LINEAR, (B250K), Marshall® TYPE, PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING. Diameter of the body of the pot is slightly smaller than a dime. Shaft length is 11.5mm. INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-V250KL-M16 $2.95 Quantity: Click on photo for larger view POT, 250K OHM X2 LINEAR DUAL, (B250K), PC MOUNT, 6 MOUNTING PINS, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING.
Diameter of the body of the pot is slightly smaller than a dime. Shaft length is 11.5mm. Fits many amps INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-V250KLX2-M16 $6.95 Quantity: 11mm Pots, D-Shaft (Marshall® Style - JCM2000 and Valvestate Version 2, Fender® Champion, Peavey Studio Pro 112) Click on photo for larger view POT, 11mm, Marshall® TYPE, PC MOUNT. Used in many later Marshall® models with PC board circuitry, including the JCM2000 series TSL100, DSL100, etc, as well as some of the late 90's ValveState models.
This pot has 4 pins. Includes mounting nut. Available values: B5K, B10K, A10K, B20K, B50K, A100K, B100K, A200K, B200K, A500K, and A1M. This style of pot is also used in the Engl Screamer 50 (E335) and the Engl Thunder 50 (E320). Select Pot Value in Options Part #P-VKG-XX $6.95 Select Option: Quantity: Click on photo for larger view POT, 1 MEG AUDIO, 11mm, Fender® TYPE, PC MOUNT.
Used in the Fender® Champion 600. Fender® part number.
Includes mounting nut. This pot is also used in the Engl Screamer 50 (E335) and the Engl Thunder 50 (E320). Part #P-VKG-A1M $6.95 Quantity: Click on photo for larger view Peavey Potentiometer, Plastic D-Shaft, 11mm, PC-mount with bracket, for Peavey Studio Pro 112.
This pot has 4 pins. Includes mounting nut. NEW PEAVEY # OLD PEAVEY # VALUE STUDIO PRO 112 FUNCTION 3110900 B10K REVERB LEVEL 3110903 B20K CLEAN & LEAD MID 3110906 A100K CLEAN VOLUME 3110907 A200K LEAD PRE GAIN, LEAD HIGH 3110908 B200K LEAD POST GAIN 3110910 A1M CLEAN & LEAD LOW Part #P-VKG-XX $6.95 Select Option: Quantity: 9mm Potentiometer, D-Shaft(Marshall® Style - MG100FX, etc) Click on photo for larger view POT, 10K LINEAR, 9mm, Genuine Marshall®, PC MOUNT.
LABELED 'B10K', D-Shaft. Used in the latest series of MG amplifiers - the ones with the large MG on the faceplate (see photo), such as the MG100FX. Includes nut. 10K ohms, linear taper. In the MG100FX, this pot is used in all control locations, all functions.
Original Marshall® part number M-POTP-91001. Part #P-VMG-10KL $8.95 Quantity: 16mm Potentiometer, Egnater Click on photo for larger view POT, EGNATER, PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING Used in many Egnater amp models including the Rebel, Renegade, Tweaker, and Tourmaster series. Diameter of the body of the pot is slightly smaller than a dime. Shaft length is 10mm. Click on photo for more detail. Select Pot Value in Options INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-VEG-XX $3.95 Select Option: Quantity: Click on photo for larger view POT, EGNATER, DUAL 500K OHM AUDIO, (A500KX2), PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING, MEDIUM SHAFT.
Used in the Egnater Rebel 20 and Rebel 30 as the gain control. Diameter of the body of the pot is slightly smaller than a dime. Shaft length is 10mm. Click on photo for more detail. INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-VEG-A500KX2 $6.95 Quantity: 16mm Potentiometer, Orange Click on photo for larger view POT, ORANGE™, PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING, KNURLED SHAFT Used in many modern Orange™ amp models including the AD30, Rockerverb, Dual Terror, Tiny Terror, TH30, Rocker 30, Thunderverb, and others. Diameter of the body of the pot is slightly smaller than a dime.
Click on photo for more detail. Select Pot Value in Options. INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-VOR-XX $3.95 Select Option: Quantity: Click on photo for larger view POT, ORANGE™, 1 MEG OHM X2 LINEAR DUAL, (B1M), PC MOUNT, 6 MOUNTING PINS, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING, MEDIUM SHAFT. Used in many amp models with PC board circuitry. Diameter of the body of the pot is slightly smaller than a dime.
Exact replacement for the volume control pots (both channels) on the Orange Dual Terror, AD30, and AD140 INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-V1MBX2-M16M $6.95 Quantity: Click on photo for larger view POT, DUAL 500K OHM AUDIO, (A500KX2), PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING, MEDIUM SHAFT. Used in many amp models with PC board circuitry.
Diameter of the body of the pot is slightly smaller than a dime. Exact replacement for the gain control pot on the Orange Tiny Terror. INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-V500KAX2-M16M $6.95 Quantity: 16mm Potentiometer, Vox, 1990-Present Click on photo for larger view POT, VOX, PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING Used in many later Vox amp models with PC board circuitry, including AC30C2, V9158 Pathfinder, V9159, V9310, Night Train, etc. Diameter of the body of the pot is slightly smaller than a dime.
Shaft length is 10mm. Click on photo for more detail. Select Pot Value in Options INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-VXA-XX $3.95 Select Option: Quantity: Click on photo for larger view POT, DUAL 10K OHM LINEAR, (B10KX2), PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING, MEDIUM SHAFT. Used in the Vox Tonelab ST and Tonelab EX INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-VXA-B10KX2 $6.95 Quantity: Click on photo for larger view POT, DUAL 100K OHM LINEAR, (B100KX2), PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING, MEDIUM SHAFT. Used in the Vox Tonelab ST and Tonelab EX INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-VXA-B100KX2 $6.95 Quantity: Click on photo for larger view POT, DUAL 200K AUDIO, (A200KX2), PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING, MEDIUM SHAFT.
Used as the Master Volume Pot in the Vox Night Train. INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-VXA-A200KX2 $6.95 Quantity: Click on photo for larger view POT, 10K OHM LINEAR, (B10K), RIGHT-ANGLE PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING, SOLID SHAFT, WITH BLACK CHICKEN HEAD SET-SCREW KNOB INCLUDED. VOX VALVETRONIX SERIES. Replacement for most pots in the ADxxVT Valvetronix Series.
In the AD15VT, AD30VT, AD50VT, AD60VT, and AD100VT, replaces the Gain, Volume, Treble, Middle, Bass, Edit 1 and Master Volume. In the AD60VT and AD120VT, also replaces the Presence, Drive, Level, Speed, Feedback and Depth. This pot has a solid shaft unlike the original knurled shaft, so a new compatible black chicken-head knob with set screw is included. Replaces Vox part numbers V903620015, RV1620-40-15S-B1, and VR RV160-40-15S-B10K-C0. INCLUDES NUT & WASHER (For spare or replacement nut, order the JN-1018 nut found in ) Part #P-VADK-B10K $5.95 Quantity: Click on photo for larger view POTENTIOMETER DUST CAP, for all 16mm (5/8') pots.
Slips over the case of the pot and helps keep out dust and contamination. Made by Alpha. Fits all 16mm potentiometers. Sold in packs of 4. Note: For single-gang pots only - will not fit dual 16mm pots. Part #PDC-160 $0.69 (For a pack of 4 dust caps) Quantity: Bias / Balance Pots Click on photo for larger view POT - Fender® BIAS POT 25K LINEAR, SCREW Original Fender® 25K linear bias potentiometer.
Used in the reissue '59 Bassman, reissue Hot Rod Deluxe/Deville, reissue Blues Deluxe/Deville. Original Fender® part #. Part #FBP-25KL $4.95 Quantity: Click on photo for larger view POT, 22K VERTICAL LINEAR BIAS ADJUST POT FOR Marshall® Used in many previous Marshall® models with PC board circuitry. Mounted on the main PC board - used to set the bias on the output tubes. Common failure item. This is the original Marshall® part. Body of pot is 15mm (about 5/8') in diameter.
Part #P-BPM-22KL-V $2.95 Quantity: Click on photo for larger view POT, 22K HORIZONTAL LINEAR BIAS ADJUST POT FOR Marshall® Mounted on the main PC board or turret boards - used to set the bias on the output tubes. Common failure item. This is an alternate horizontal style - particularly useful in modifications, kit builds, etc. Body of pot is 15mm (about 5/8') in diameter.
Part #P-BPM-22KL-H $2.95 Quantity: Click on photo for larger view POT, 22K VERTICAL LINEAR BIAS ADJUST POT - MINIATURE Smaller than the standard Marshall® style vertical pot, the body of this pot is 10mm in diameter (3/8'). Not recommended for Marshall® due to the smaller size, but very useful in project builds and adding a bias control to amplifiers which do not have one and space is an issue (such as the Fender® Blues Junior, for example). Part #PT-22KV $1.99 Quantity: Click on photo for larger view POT, 22K HORIZONTAL LINEAR BIAS ADJUST POT - MINIATURE Smaller than the standard Marshall® style pot, the body of this pot is 10mm in diameter (3/8'). Not recommended for Marshall® due to the smaller size, but very useful in project builds and adding a bias control to amplifiers which do not have one and space is an issue (such as the Fender® Blues Junior, for example). Part #PT-22KH $1.99 Quantity: Click on photo for larger view TRIM POT, 20K Ohms.
This 6mm pot may be used to modify some amplifiers and install a bias adjust control. With some design work, may be used in the Fender Blues Junior, for example. 20K ohms, 0.6 watt. Part # TP-20K $1.69 Quantity: Click on photo for larger view TRIM POT, 50K Ohms.
This 6mm pot may be used to modify some amplifiers and install a bias adjust control. With some design work, may be used in the Fender Blues Junior, for example. 50K ohms, 0.6 watt. Part # TP-50K $1.69 Quantity: Click on photo for larger view MULTI-TURN TRIM POT, 25K Ohms.
This 3/8' X 3/8' X 1/4' pot may be used to modify some amplifiers and install a bias adjust control. 25k Ohms, 0.5 watts, 25 turns. Allows a very precise bias adjustment which is immune to changing due to amp chassis vibrations.
Part # MTTP-6501 $2.79 Quantity: Click on photo for larger view POT - Fender® BIAS POT 10K LINEAR, SCREW Original Fender® 10K linear, screw, bias potentiometer. Used in vintage blackface and silverface models. Original Fender® part #. Includes lock washer, smooth washer and nut.
Part #P-BPF-10KL $4.95 Quantity: Click on photo for larger view Fender ® HUM BALANCE CONTROL - 100 OHMS Used on Fender amps starting in the mid 1970s for hum balance adjustment with a screwdriver from the rear panel. Includes mounting nut. Original Fender part number (or 028421). Part #FHB-421 $9.95 Quantity: Bias / Balance Pots - Fender® Click on photo for larger view POT - Fender® BIAS POT 10K LINEAR, SCREW Original Fender® 10K linear, screw, bias potentiometer. Used in vintage blackface and silverface models.
Original Fender® part #. Includes lock washer, smooth washer and nut. Part #P-BPF-10KL $4.95 Quantity: Click on photo for larger view Fender ® HUM BALANCE CONTROL - 100 OHMS Used on Fender amps starting in the mid 1970s for hum balance adjustment with a screwdriver from the rear panel. Includes mounting nut.
Original Fender part number (or 028421). Part #FHB-421 $9.95 Quantity: Click on photo for larger view POT - Fender® BIAS POT 25K LINEAR, SCREW Original Fender® 25K linear bias potentiometer. Used in the reissue '59 Bassman, reissue Hot Rod Deluxe/Deville, reissue Blues Deluxe/Deville.
Original Fender® part #. Part #FBP-25KL $4.95 Quantity: Potentiometers - Fender® & Others Click on photo for larger view POT - CTS, 3/8' BUSHING Top quality 24 mm carbon composition. 300 ° rotation. 1/2 watt, 500VDC rating.
1/4' diameter solid metal shaft, 3/8' bushing, solder lugs. Fits perfectly in vintage amps like Fender® (Tweed, Brownface, Blonde, original Blackface and original Silverface Models), all Marshalls up to 1979 and some of the JCM800 versions, vintage Vox, vintage Orange, vintage Hiwatt, vintage Boogie, Sound City and many more. With correct 1/4' shaft and 3/8' bushing.
Superior quality, solderable back! CTS was the original OEM supplier for vintage Fender® pots. Note: 250K J-Taper, 1 Meg J-Taper, and 3 Meg Reverse Audio (C3M) pots have brass colored shafts. Select Pot Value in Options INCLUDES NUT & WASHER (For spare or replacement nut, order the JNUT-38 nut found in ) Part #P-VC-XX Starting at $3.95 Select Option: Quantity: Click on photo for larger view POT - CTS, 3/8' BUSHING, NYLON SHAFT Top quality 24 mm carbon composition. 300 ° rotation. 1/2 watt, 500VDC rating.
1/4' diameter nylon shaft, 3/8' bushing, solder lugs. Exact fit for hand-wired American made amplifiers such as vintage Fender® and others. Nylon shaft pots were used in most Fender silverface series amps from the late 60s and 70s. CTS was the original OEM supplier for vintage Fender® pots.
INCLUDES NUT & WASHER (For spare or replacement nut, order the JNUT-38 nut found in ) Part #P-VCT-XX $3.50 Select Option: Quantity: Click on photo for larger view FENDER ® SILVERFACE MASTER VOLUME POT - 1 MEG AUDIO, 8mm BUSHING, WITH DPST PULL SWITCH Finally - a solution to the 'no longer available' original pull-switch master volume pot in CBS Fenders from the mid to late 1970's. 24 mm, 300 ° rotation. 1/2 watt, 500VDC rating, with DPST pull switch. A good replacement for the pull-switch master volume in Fender® silverface amps from 1974-1982.
The brightness capacitor is installed from the center terminal to the end terminal in this application. For replacement nut, order our JN-1016.
INCLUDES NUT & WASHER Part #P-V1MA-MV $8.95 Quantity: Click on photo for larger view POT, Revisit™, 3/8' BUSHING, 24mm, SMOOTH SHAFT. 24 mm carbon composition. 300 ° rotation. 1/2 watt, 500VDC rating. 1/4' diameter shaft, 3/8' bushing, solder lugs.
Exact fit for hand-wired American made amplifiers such as vintage Fender® and others. Select Pot Value in Options INCLUDES NUT & WASHER (For spare or replacement nut, order the JNUT-38 nut found in ) Part #P-38-XX Starting at $1.99 Select Option: Quantity: Click on photo for larger view POT - Revisit™, 24mm BODY WITH 8mm (5/16') BUSHING 24 mm carbon composition, economy priced.
Available in A50K, B50K, and A250K values. Select Pot Value in Options NOTE THAT THIS POT HAS AN 8mm (5/16') BUSHING, NOT 3/8'. INCLUDES NUT & WASHER Part #P-VA-XX $1.99 Select Option.
Hey forum, I did my research and have some opinions. I plan on buying my first quality amp. I'm thinking about getting a used Marshall JCM 2000 DSL 50w Head and a Marshall 1960a 4x12 Cabinet which are both made in the U.K. Has anyone tried this amp? It seems versatile and works well with effect pedals. I found a nice condition used head for $600 including the foot switch (I might be able to get it even cheaper). The head had a professional tube change from EL84s to EL34s in late 2015.
I can get a nice condition cabinet for $400-$500. What do you guys think? This would be my first step into the tube amp world. I've had both the 50 and 100w version of the JCM series and the 100w straight DSL from Vietnam.my thoughts The Vietnam DSL 100 is my favorite of the three.and the one I've kept! The resonance knob control is miles more versatile than the shelving filter button. The crunch channel has a mid peak that's a little higher than the JCM versions and cuts better in a mix with cleaner note definition.
Don't let the Vietnam thing concern you, these heads are extremely reliable as their U.K. Counterparts or even more so as the circuits have been improved with development.
The JCM2000 100w is second for me with less compression and just seems to breathe a little easier than the 50w The 50w is by no means a slouch and isn't far behind the others IMO.I could live with all of them! I have a DSL 50 - love it!
The amp is extremely versatile. Classic rock crunch, 80's hair metal, modern high gain and everything in between. Plus, it has a.fantastic. glassy clean channel, that is pretty damned close to my vintage Hiwatt DR-103 - I'm not kidding. In fact, the clean channel is so good that I actually use my DSL on clean with a Carl Martin Plexitone drive pedal to get cranked plexi tones at a much more usable level. The DSL's overdrive is great at jamming levels, but in my experience, to hit the sweet spot it needs to get a bit louder than I want when the wife and kids are at home, so with a quality drive pedal you get the best of both worlds with this amp.
Plug straight in and rock out if you are jamming or gigging, or use a great drive pedal at TV levels. I bought mine for $500 CDN which equates to approx $375 USD. It's a 2007 model that was in like-new condition when I bought it 2 years ago. It is trouble-free. Here's some tones: 1) Cranked and compared to a EVH 5150 III. The DSL sounds better to me, the mids are more classic and forward.
2) Paul Gilbert was using these on tour for a few years and said 'these just always sound consistent and good and rock.' Skip to 3:30 in the video for the amp rundown.